Semi-automated Flow Injection Method for the Determination of Iron ( II ) By 1 , 10-Phenanethroline

The research is included determination of Fe(II) via its reaction with 1,10-phenanethroline to form light-red complex which is absorbed at λ max =510 nm. Home-made flow injection valve is designed with two loading loops, L1 and L2. A series of studies are conducted represented by fixing physical and chemical optimum conditions, dead volume, repeatability, dispersion coefficient, construction calibration graph, and application of the method. The dead volume is zero for the system which it has high repeatability (n=8) with RSD and SD 0.6 and 0.05 respectively. The dispersion coefficient is 1.68 at the concentration 10 ppm. The range of measurements of calibration graph is (0.05-18.00) ppm with limit of detection (S/N=3) 0.05 ppm.


INTRODUCTION
Flow injection analysis (FIA) method is used in various analytical fields, which has a prominent role in agricultural, industrial, pharmaceutical and environmental fields.Flow injection technique is discovered and patented by the researchers Ruzicka, Hansen, and Stewart in 1975 1 .One of the main flow injection technique features are the ability of analysing the very small volumes of samples and reagents, high sampling rate, low detection limits, wide extent of concentrations, ability of miniaturization of the apparatuses, high repeatability of readings, less personal mistakes comparatively with the other techniques, and conversion the reactions of open system to the reactions of closed system 2-6 .
The FIA system consists of many parts such as, peristaltic pump, manifold, detector, and recording device of signal 7 .Flow injection valve is the most important part of the manifold and considered as the heart of FIA system, which is used for injecting the chemical reaction solutions [8][9][10][11] .The sample-reagent segment is formed after loading process of the reaction components toward the detector by carrier stream rapidly 12 .When the sample-reagent segment reaches to the flow cell inside the detector, the signal is recorded as a sharp peak.The signal with height, area, and width is recorded with time of sample analysis 13 .Iron is the most common element in Earth, which is never found in free elemental state, therefore, iron is extracted from its ores.Iron is considered as one of the essential trace elements in biological systems.The average amount of iron is over than 4 g in human body.Iron plays very important roles in biological systems including O 2 transport in haemoglobin, regulation of gene expression, and regulating electron transfer, radical, and redox catalysis in enzymes 14,15 .
The phenanthroline (phen) or 2,2'-bipyridine (bipy) reagent is heterocyclic organic compound with the formula C 12 H 8 O 2 and absorbs at a wavelength of 265 nm.Phenanthroline reagent is in the form of white-colored crystalline and characterized by the formation of strong complexes with most metal ions so it is used as a common ligand in coordination chemistry.It is binds metals more tightly since it has two chelating nitrogen donors.[Fe(phen) 3 ] 2+ complex is called as "ferroin" and well-studied which is characterized with deep red-colored and stable in acidic medium 16,17 .1,10-phenanthroline is used for the determination the trace amount of Fe (II) and has the chemical structure in Figure .1.secondly injecting the sample of Fe (II), thirdly injecting the solution containing the reagent 1,10-phenanthroline, the buffer solution (pH= 5), and hydroxyamine hydrochloride and fourthly loading the injected solutions to the detector with helping of the carrier stream.The Fig.The aim of this research is designing flow injection system for the determination of Fe (II) including home-made flow injection valve from available, inexpensive, and environmentally friendly materials.The proposed method has many features such as, rapidity, low cost, low consumption of reagents, and satisfactory results.

EXPERIMENTAL Designing Stages of Flow Injection Valve
An integrated flow injection unit is designed for the determination of Fe (II) by using home-made valve with capacity loading of two solutions at certain stages, including firstly pumping the water as a carrier solution to the system, Buffer solution: first, 0.1 M of glacial acetic acid -with specific gravity 1.05 g.L -1 and percentage 90%-is prepared followed by dissolving 1.0 g of sodium acetate trihydrate in glacial acetic acid solution to get 0.1 M of buffer solution.

Calibration of Pump Speed
This study is conducted to calibrate the speed of the peristaltic pump and calculate the volume for the solutions per minute at different values of pump speed by using stopwatch.The results are illustrated in table (2) and Figure (6).The chemical reaction between Fe (II) and reagent requires the mixing of four solutions: the sample Fe (II), the reagent 1,10-phenanthroline, hydroxylamine hydrochloride solution, and buffer solution.The quaternary home-made valve makes the loading of four solutions easier and more quickly via injecting these solutions into two loops only.L1 and L2 represent to the two loops of the valve which their volumes and capacities are calculated by using the relation V=π r 2 L, as shown in table (1).

Table.1: Calculation the volumes of injection valve loops
Seq.
Length of Loop L (cm) Volume V No.

Optimum position for lnjecting sample & reagent
Choosing the optimum position effects on the value and the sensitivity of the response when the solutions are injected into the valve at different volumes and capacity of loops.The effect of position replacement for both Fe (II) and reagent is studied at λ max =510 nm, 12 ppm of Fe (II) and 1,10-phenanthroline reagent, flow rate of 3.1 mL.min -1 , and length of reaction coil is 35 cm.Table (3)  and Fig. (7) show that the injecting of 1,10-phenanthroline reagent and Fe (II) into L1 and L2 -with the capacities 78.50 μL and 235.71 μL respectively-results in response with 4.5 cm of height.The changing of injecting positions results in response with 6.9 cm of height and this is agreed with the literatures 16,17 .
Studying the effect of changing flow is conducted at λ max =510, 12 ppm of both sample and reagent, the injection positions are L1 and L2 for sample and reagent respectively, and the length of reaction coil is 35 cm.The range of flow rate is (1.9-4.3)mL.min -1 and the results are illustrated in table (4)  and Figure (8).

Effect of Carrier Stream Flow Rate
The dilution is lesser at slow flow rates because decreasing flow rate increases the sample retention time before moving to the detector and the interaction between the sample and the detector reaches the state of equilibrium and therefore the response will be higher at slow flow rate 22 .The slow flow rates show a wide, double, and distorted peak.According to table (4) and Fig. (8), the increase in flow rate from 1.9 to 3.1 mL.min. - , the response gradually increases from 3.7 to 5.8 cm, because the slower flow rate that provides longer time causes a dilution of the sample by the carrier stream solution.But at the higher flow rates, the shortest time for dilution of the injected sample is occurred and the response increases to 3.4 mL.min -1 .When the time is optimal and the samplereagent segment dilution is reduced, the response is reached to the maximum height at 7 cm.Then increase the flow rate from 3.9 to 4.3 mL.min -1 causes the response to be constant at a height of 5.3 cm.The very high flow rates cause the solutions not to be fully mixed and lack equilibrium state of the reaction, therefore the response is reduced [23][24][25] .

Reaction Coil Length
The length of reaction coil effects on the reaction and the fully mixing of the solutions to reach to equilibrium state.Also, shape, diameter, and length of the reaction coil effect on the formation of sample-reagent segment at the optimal time, and the sampling rate.
The effect of reaction coil length is studied at λ max =510 nm, the concentration of 12 ppm of Fe (II) and 1,10-phenanthroline reagent, flow rate=3.4mL.min -1 , and the injection positions of Fe (II) and 1,10-phenanthroline reagent are via L1 and L2 respectively.The effect of reaction coil lengths is studied at the range (35-175) cm.The results are shown in table (5) and Figure (9).

Relationship between Reaction Coil Length and Response
According to table (5), the increasing of reaction coil lengths from 35 cm to 60 cm leads to increase the height of response from 2.8 cm to 3.0 acutely.The reaction coil of length 35 cm does not allow good mixing for the reaction components but, the lengths 60 cm, 90 cm, and 115 cm provide sufficient time for good mixing and reaching equilibrium state which causes maximum height of response at reaction coil length of 60 cm.Fig. (9)  shows reducing in the response height when the length of reaction coil is increase to 175 cm due to high dilution of sample-reagent segment.Especially, the reaction between Fe (II) and 1,10-phenanthroline reagent is rapid and there is no need for further mixing to reach equilibrium state 26 .

Repeatability
Repeatability is repeating process of injection-at least six injections-at the same conditions to prove the precision of injection for the system 27,28 .The repeatability is studied for eight injections (n=8) at the same optimum conditions including: λ max =510 nm, the concentration of 12 ppm of Fe (II) and 1,10-phenanthroline reagent, flow rate=3.4mL.min -1 , reaction coil length=60 cm, and the injection positions of Fe (II) and 1,10-phenanthroline reagent are via L1 and L2 respectively.Standard deviation S.D and relative s Standard deviation values are 0.05 and 0.6 respectively.The results are illustrated in table (6)  and Figure (10).

Dispersion Coefficient (D)
Dispersion coefficient is studied through the comparison the form and height of response before dilution (H 0 ) and after dilution (H max ) after fixing the optimum conditions, as illustrated in table (7) and Fig. (11).It has to be noted that the response height is reduced with dilution.The dispersion coefficient (D) is calculated as follows 29 : D=13.1/7.8=1.68 The dispersion coefficient value 1.68 means that the dilution is limited and considered in favor of the system.components and response appearance ascending to the maximum peak followed by the descending of response to the baseline.It is found that the time of analysis for one sample is 55 seconds; hence, the sampling rate is about 66 sample per hour, The sampling rate of about 66 sample per hour is considered good result according to the literature 32 .

Calibration Graph
This study is conducted at λ max =510 nm after fixing the optimum conditions including: 12 ppm of 1,10-phenanthroline reagent, flow rate =3.4 mL.min -1 , reaction coil length=60 cm, and the injection positions of Fe (II) and 1,10-phenanthroline reagent are via L1 and L2 respectively.The range of Fe (II) concentrations is (1.0-18.0)ppm with limit of detection (LOD=3.3S/N)0.05 ppm and the results are illustrated in table (8)  and Fig. (12) in details.

Table.7: Response with dilution and without dilution
Response without Response with Dispersion dilution (H 0 ) dilution (H max ) coefficient (D) 13.1 cm 7.8 cm 1.68

Dead Volume
Dead volume is the remaining volume of any component of chemical reaction during loading process of solutions into injection valve.Dead volume is considered as a measure of FIA system efficiency.If the value of dead volume is not zero, that causes appearance of signal in the baseline.In this case, the injection valve is imperfect but the zero value of dead volume proves the high efficiency of FIA system.It has to be noted that all responses have the same baseline because the dead volume is zero 30,31 .

Sampling Rate
Sampling rate is the number of analysed samples per one hour.The time of sample analysis is calculated from injection stage of reaction (2),(3),(4), and (5) show the four stages mentioned above in details.

Fig. 8 .
Fig.8.Effect of changing flow rates on the sensitivity of response

Fig. 9 .
Fig.9.Relationship between Reaction Coil Length and Response